Retraining ReportJob training public funding can pay for

Find training

CNC machinist training in Texas

82 CNC machinist programs with costs, results and funding that can make them free

Texas has more approved machinist and CNC programs than any other state, 82, and 26 of them are in Houston, Pasadena, Conroe and Cypress. The quickest and cheapest, 14 CNC and machine operator courses at about $2,000, also had the highest early earnings, an estimated $48,200 a year, against about $40,000 for the longer machinist certificates and degrees. Completion is low, 48% in the typical program against 71% across the US. CNC operator jobs are shrinking nationally, and Texas expects a 5% drop by 2034, half the US decline.

No school dominates: 31 schools run the 82 programs, none more than 7.

As across the US, about 38% of the programs here take students without a high school diploma; the rest ask for one or for earlier courses.

By kind, the 82 programs here are machinist certificate or diploma (48 programs), machinist (associate degree, 17 programs), CNC or machine operator (14 programs), short course or single class (2 programs), and 1 more of one other kind. The cheapest kind here is CNC or machine operator, at $2,004 for the middle one of 14 with a price; the most expensive is machinist (associate degree), at $6,569.

More of them can be taken online or hybrid than across the US: 59 of 82, against 32% nationwide. They're spread over 26 cities, none with more than 10. Nearly all (78 of 82) are at schools on the Department of Education's list of accredited institutions.

What a CNC machinist does and how you become one: CNC machinist training across the US

See the 82 programs

How much does CNC machinist training cost in Texas?

Certificates and short courses (65 programs)
$1,944 to $5,357most of them
Two-year degrees (17 programs)
$6,317 to $12,780most of them

What you pay yourself for the whole program, as the schools report it. "Most" is the middle half of the programs with a price.

In the typical program

Finished the program
48%
US: 71%
Working 6 months later
75%
US: 80%
Earned a year, estimated
about $42,100
US: about $40,700
Length
Not enough data
Only 5 of 82 programs report it

US Department of Labor data, program year 2024; only programs approved for workforce funding, so not every school in Texas. How these figures are made

What CNC tool operators earn in Texas

$48,480 typical pay a year in May 2025; most earn $39,380 to $59,760

Across the US: $50,690 a year.

Jobs now
about 13,190
Change to 2034
−5% US: −11%
Openings a year
about 1,110

Pay of everyone working in the job, not only graduates of these programs. Pay and jobs: Bureau of Labor Statistics1; change and openings, 2024 to 2034, from the Texas labor market office, openings counting people who leave or change jobs2.

Is there free CNC machinist training in Texas?

All 82 CNC machinist programs in Texas approved for WIOA funding

Filters
What you need to enroll
Kind of program
School
How it's taught
How to show the list

82 programs

How to pay for CNC machinist training in Texas

WIOA funding can pay for CNC machinist training in Texas

All 82 programs on this page are approved for it. Whether you qualify, how much your local area pays and how to apply are on our page Does WIOA pay for job training?

Paid machinist apprenticeships

An apprenticeship is a job: you're paid to learn, and you apply to the employer or the sponsor, not a school. None of the programs on this page is one.7

Financial aid and grants for CNC machinist training

Most students can get federal student aid for college, career school or trade school, and a Federal Pell Grant, unlike a loan, usually doesn't have to be repaid. 78 of the 82 programs here are at schools on the Department of Education's accreditation list; the rest may qualify too. Check with the school before you count on it.89

GI Bill for CNC machinist training

Veterans, service members and qualified dependents can use GI Bill benefits for non-college training programs. The list doesn't record which of these 82 programs the VA approves, so ask the school or the VA.10

Quick facts: CNC machinist training in Texas

programs with a price cost under $2,000
23 of 82
lowest typical price among the states with enough programs to compare
14th of 34
other states where the typical program's graduates earned less
8 of 15
CNC machinist programs of any state: no state has more than Texas
Most

The same figures as the CNC machinist training by state table; prices only for states with three or more schools.

Do pricier CNC machinist programs in Texas have better results?

No, if anything the reverse. The pricier half of CNC machinist programs in Texas typically costs $8,356, about 4 times as much as the cheaper half's $2,004, yet the share finishing and earnings came out lower and the rest held about level. In the pricier half, 47% finished, against 60%; graduates earned about $42,200 a year, against about $45,700; 72% were working six months later, against 73%.

Two groups side by side can't tell you what one school will do for you, and programs differ in who enrolls. To weigh single programs, sort the list by price or by earnings.

How this is worked out: the 27 certificates and short courses here that report both a price and results, split at the middle price into two halves of 13; degrees are left out. A typical figure needs five programs in a half. Source: US Department of Labor, program year 2024; earnings are the second quarter after leaving, times four.

Machinist apprenticeships in Texas

A machinist apprenticeship is usually run by an employer. It combines paid training on the job with related classes and lasts several years.11

You apply to the employer or the program sponsor, not through a school.7 The Department of Labor's Apprenticeship Finder lists openings by place and job. None of the CNC machinist programs on this page is an apprenticeship.

CNC machinist training in Houston, Dallas, Corpus Christi and other Texas cities

Areas with 10 or more programs have a page of their own. Choosing another area filters the program list above. 15 more programs are in 10 other areas and 16 online.

Other training in Texas

How CNC machinist training compares with the rest of skilled trades: Trade school programs in Texas

Where the Texas machinist program numbers come from

The 82 machinist programs here are the ones Texas approved for WIOA funding (public workforce funding under the Workforce Innovation and Opportunity Act) as of June 30, 2025, from its eligible training provider list (ETPL),12 as reported to the US Department of Labor for program year 2024 (July 2024 to June 2025). 31 schools run them, and 40 of them report how past students did. Schools that never applied for approval are missing.

Prices are tuition and required fees for someone paying without workforce funding, as each school reported them; results describe past students, so they are no guarantee. Where the numbers come from explains every figure, and what "Not reported", "Left out" and "Not enough data" mean.

Sources for the facts about CNC machinist training in Texas

Show the 12 sourcesHide the sources
  1. US Bureau of Labor Statistics, Occupational Employment and Wage Statistics, May 2025, all data file: 51-9161 Computer Numerically Controlled Tool Operators
  2. Projections Central, long-term occupational projections 2024 to 2034 (US Bureau of Labor Statistics and state labor market information offices): Computer Numerically Controlled Tool Operators
  3. US Department of Labor, TrainingProviderResults.gov: About This Site
  4. US Department of Labor: WIOA Adult Program
  5. Code of Federal Regulations, title 20, part 680, sections 680.220, 680.230 and 680.310: career services before training, other grants such as Pell Grants first, and limits on Individual Training Accounts (GovInfo, 2024 edition)
  6. US Department of Labor: American Job Centers
  7. US Department of Labor, Apprenticeship.gov: Discover Apprenticeship: Earn While You Learn Today (fact sheet)
  8. US Department of Education, Federal Student Aid: Eligibility for Federal Student Aid
  9. US Department of Education, Federal Student Aid: Don't Miss Out on Federal Pell Grants
  10. US Department of Veterans Affairs: GI Bill benefits for non-college degree programs
  11. US Bureau of Labor Statistics, Occupational Outlook Handbook: Machinists and Tool and Die Makers
  12. US Department of Labor, Training and Employment Guidance Letter 8-19, Attachment I: Requirements for Training Providers, Program Eligibility, and the State Eligible Training Provider (ETP) List